零件名稱Parts：

　　1、主體Hub

　　2、摩擦片F(xiàn)riction Plate

　　3、稱環Lining Ring

　　4、壓板 Pressure Plate

　　5、蝶形彈簧 Disc Spring

　　6、導向壓板 Pilot Plate

　　7、調節螺母 Adjusting Nut

　　8、調節螺栓 Adjusting Bolt

　　9、鎖緊螺釘 Locking Screw

　　10、止退墊片 Gaskot

　　旋轉角度和扭矩設定 Set the Rotation Angle and Torque

　　選型SELECTION

　　1.依據負載條件或設備本身的力的大小來決定所需打滑扭矩。如果設備負載條件不清楚，請將打滑扭矩設為馬達產

　　生在承載限扭裝置的軸上扭矩的1.5-2倍。

　　2.選用限扭裝置時，應選擇有足夠大的扭矩范圍和孔徑范圍。

　　3.根據兩個摩擦片中間夾的中心元件的厚度來決定選擇最合適的襯環寬度。

　　The required sliding torque is set depends upon the loading or the force of the equipment. If the loading conditions are not clear, please set the sliding to que as 1.5-2 times of one upon the shaft that carries the Torque Limiter. Please select the Torque Limiter with sufficient torque and aperture ranges.

　　Select optimum lining ring length according to the center part thickness clamped between the two friction discs.

　　扭矩的設定TORQUESETTING

　　限扭裝置扭矩的設定是依靠上緊和松開調節螺栓和/或調節螺母來實現的。針對RTL50到RTL89，依靠調節螺母;針對RTL127和RTL178，依靠調節螺栓。

　　Tight and loose the adjusting bolts and/or nuts to set the torque of the Torque Limiter. The Limiter form size RTL50 to RTL89 depend upon the adjusting nuts, whereas RTL127 and RTL178 depends upon the adjusting bolts.

　　扭矩的設定可以在將限扭裝置安裝在軸上后進行，過程是：

　　Set the torque after mounting the Limiter upon the shaft as follow:

　　RTL50到RTL89的規格

　　For sizes form RTL50 to RTL89

　　首先，用手旋轉上緊調節螺母，以至固定碟型彈簧和壓板;

　　Rotate to tight the adjusting nuts by hands to fix the disc spring and plate;

　　然后，試著用扳手將螺母上緊，約60度。

　　Then, try to tight the nuts (about 60℃)by wrench

　　RTL127到RTL178的規格

　　ForsizesformRTL127toRTL178

　　首先，旋轉螺母，固定碟型彈簧和壓板，再上緊每一個調節螺栓，約60度。

　　First, rotate the nuts to tight the disc spring and pressure plate. Then tight all the adjusting bolts (about 60℃)

　　然后，如果限扭裝置在正常負載條件下能夠打滑，請逐漸上緊螺母(RTL50到RTL89)或螺栓(RTL127到RTL178)，直到限扭裝置停止打滑。請務必保證均勻上緊(或松開)每個螺栓。

　　If the Limiter slides with normal loading,please tight the nuts (for sizes form RTL50 to RTL89) or bolts (form RTL127 to RTL178) generally until the Limiters stop sliding. Please ensure that each bolt is tightened or lossened averagely.

　　通過這樣的幾次測試，來找到適合設備的限扭設定。下表顯示有效旋轉角度和限設定的關系，供參考。

　　Find out the setting torque appropriate for the equipments after tests. Please refer the following Table that shows

　　the relationship between the effective rotation angle and torque setting.

　　為了精確扭矩設定，推薦試運行一次限扭裝置，比如，在當轉速50-60rpm,500轉時，旋轉調節螺母貨螺栓45度。

　　To make torque setting precisely, we recommend you to use Torque Limiter for trial once. For example, while the rotation speed is 50-60 rpm with 500 circles, rotate the adjusting nuts or bolts around 45℃

　　CENTERPARTS中心元件

　　1.中心原件的摩擦表面應加工，以保證額定轉矩，以及平面度、平行度、與孔一致和防銹、防油污。推薦表面粗糙度為Ra1.6。如果中心元件不能滿足以上技術要求，打滑扭矩將不穩定。

　　2.請按下表來加工中心元件的孔，和選擇最小鏈輪齒數和襯環寬度。

　　Process the friction face of center parts to ensure the rated torque, planeness and parallelism in line with the bore and protect the parts from the rust and oil. The recommended surface roughness(Ra) is 1.6. The sliding torque will be not stable if the center part is defected.

　　Please process the bore of center parts according to the following Table and, select sprocket with min. teeth number and lining ring length.